You Are Here: Home » Blog » Guide » How to Reduce Needle Breakage in Circular Knitting Machines

How to Reduce Needle Breakage in Circular Knitting Machines

Views: 0     Author: Site Editor     Publish Time: 2026-11-09      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

In a circular knitting mill, a broken needle is never just a broken needle. A single failure stops the machine for ten to thirty minutes, leaves a needle line running the full length of the roll, and often takes two or three neighbouring needles with it. On a 30 inch, 28 gauge cylinder, even a modest breakage rate becomes a steady drain of spare parts, lost output and quality claims.

Most circular knitting machine needle breakage is preventable, and it almost always traces back to a mechanical fault in the knitting zone, a yarn that is too tense, too hairy or too contaminated, a mismatched or worn needle, or a process setting that pushes the machine beyond what the yarn and fabric can support. The needle is usually the last component to fail, which is why replacing it without diagnosis rarely stops the problem.

The sections below show how to find the real cause, correct it, and hold the breakage rate down.

What Are the Most Common Causes of Needle Breakage?

Breakage clusters around four families: mechanical wear in the cams, sinkers and cylinder, yarn-induced stress, needle selection and handling errors, and process conditions such as lubrication, speed and take-down tension. Mechanical and yarn causes account for most incidents, and both are fully correctable through inspection and correct settings rather than through buying more needles.

The families are easy to confuse because they interact. A worn cam raises the impact load on every needle butt, and a tension set slightly high removes the margin that would have absorbed it, so the operator blames the yarn while the cam is the real fault.

Failure family

Typical signature

Mechanical wear

Repeats at the same feeder or sector, often after a light clicking sound

Yarn-induced stress

Spreads randomly and tracks specific yarn lots or colours

Needle condition

Early failures, frequently with bent hooks or stiff latches

Process settings

Rises after a speed increase, fabric change or maintenance stop

Why the Needle Is Usually the Victim

A latch needle in a running cylinder completes tens of thousands of stitch cycles per hour, its butt riding the cam track and its latch snapping shut on a rivet. The construction of a latch needle concentrates that work into three small zones, and each one is a fatigue point. Because the needle is the cheapest and most highly loaded part in the assembly, it fails first and reports a problem that belongs to something else.

How to Read the Breakage Pattern Before You Replace a Needle.webp

How to Read the Breakage Pattern Before You Replace a Needle

Where needles break tells you which subsystem to inspect. Breakage fixed at one feeder points to a local mechanical fault, breakage spread across the cylinder points to yarn or settings, breakage on one side points to alignment, and mass failure in a single revolution points to a foreign object or a drive fault.

Before restarting, note four things: the feeder number, where the failed needles sit around the cylinder, how many failed at once, and whether the fabric shows a line at that point.

Breakage at One Fixed Feeder Position

Repeat failures at one feeder indicate a fault confined to the few centimetres of track those needles cross. The usual candidates are a cam profile worn into a step or burr, a yarn guide set too high or too low, a damaged sinker, or debris packed into one trick. A machine overhaul is unnecessary: replace the components at that position and run the machine empty for several revolutions to confirm the repair.

Breakage Spread Around the Cylinder or On One Side

Random failures point to something distributed across the machine, which means tension set too high for the count, hairiness shedding fibre into every trick, uneven oil delivery, or a mixed population of needles. Breakage on one side points to alignment instead: machine level, cylinder and dial concentricity after a rebuild, or take-down pulling harder on one side. Random breakage responds to measurement, alignment faults respond to a gauge.

Breakage pattern

First action

Same feeder, repeatedly

Replace or dress that cam, check yarn guide height and sinker

Random across the cylinder

Measure tension at every feeder, check hairiness and oil

One side or one sector

Check machine level, concentricity and take-down balance

Many needles at once

Stop, clear the zone, inspect belts and timing

Mechanical Causes: Cams, Sinkers and Timing

Worn cam tracks, damaged sinkers, worn tricks and lost timing are the most destructive mechanical causes, because a single worn component can break dozens of needles in one run while the machine still sounds normal. Tolerances in the zone are measured in hundredths of a millimetre, so wear that looks cosmetic on a bench becomes load on the needle in production.

The zone is a precision assembly in which needles, sinkers and cams interact continuously at speed, and nothing in it has spare capacity.

Cam Track Wear and Butt Impact

Every butt strikes the cam track thousands of times per hour, and the track develops a groove where the butts run whose edges become sharp. A sharp edge does not guide the butt, it hits it, and the impact travels down the needle shank. Loose cam box screws add a second problem, because the assembly shifts under load and needles deviate as they accelerate hardest. Any cam showing a step, scoring or a bright wear mark should be replaced as a set.

Sinkers, Trick Clearance and Lint Packing

Sinkers hold the old loop down while the needle rises, so worn tips form longer loops and let the fabric ride up, while bent sinkers foul the needle path. The tricks fail in the opposite direction: tricks worn wide let the needle float and vibrate, while tricks packed with fly and metal dust block vertical travel until the butt is forced over the cam. Clean the tricks weekly and renew sinkers in complete sets.

Timing and level belong in the same inspection. After a cylinder change, dial adjustment or cam replacement, timing must be reset and verified before the machine returns to production speed, because a machine slightly out of phase will still run while its needles meet sinkers and guides instead of passing them. Level matters for the same reason in a different plane: an out of level cylinder loads one side of every needle path more heavily.

Lubrication, Speed and Machine Load

Insufficient or incorrect lubrication raises friction throughout the zone and is one of the most underestimated causes of breakage, while running above the designed speed or above what the fabric tolerates multiplies every other stress in the machine. Both are process variables, so both are free to correct and neither needs new parts.

Oil Type, Quantity and Delivery

Oil reaches the needle through the trick, and a dry trick turns the shank into a wear surface. Use a dedicated needle oil with a viscosity matched to the machine and workshop temperature, delivered at a rate that keeps a continuous film on the cam track. Atomised delivery covers the tracks more evenly than brush application, but only if nozzles are aligned and lines are clear, and blocked lines produce dry patches invisible from outside that break needles in one sector only.

Speed, Take-Down Tension and Elastic Fabrics

Raising revolutions per minute increases both the number of impacts per hour and the energy of each one, so fatigue life falls faster than output rises and the gain is usually returned as downtime within weeks. Take-down tension is the second load path: excessive pull from the spreader resists loop clearing and loads the hook from below, which is why elastane fabrics break needles at settings that are safe for cotton.

Circular Knitting Machine and Flat Knitting Machine Manufacturer.jpg

Yarn is the most under-diagnosed contributor to breakage. Excessive or uneven tension bends the hook, knots and slubs deliver impact loads the needle was never designed to survive, and contamination packs the tricks and raises friction on every stroke. In mills where maintenance is already disciplined, yarn is where the remaining breakage lives.

Tension That Bends the Hook

When tension is too high, the yarn pulls the hook forward during loop formation, so the hook opens slightly further on every cycle than its design allows. The deformation is elastic at first and permanent later, and a hook pulled open will not close cleanly against the latch. The commoner problem is uneven tension between feeders, which produces breakage that looks random until each position is measured.

Knots, Slubs and Abrasive Yarn

A knot cannot pass through the hook at normal tension, so it arrives as a resistance spike that slams the latch against the hook until the rivet and latch seating fatigue. Abrasive yarn works more slowly, polishing a groove into the hook and trick wall until the groove becomes a burr that cuts the yarn and damages the next needle. Check yarn cone by cone, and set cleaners and tensioners for the count actually being run.

Storage Humidity and Yarn Conditioning

Yarn from a dry warehouse is brittle and sheds fibre, while yarn that has taken up moisture runs with a higher friction coefficient and packs the tricks faster. A lot that passed laboratory tests in one season can behave differently in a monsoon month, which is why some mills see breakage rise with the weather rather than with any change on the machine. Condition yarn to the workshop and hold humidity stable in the knitting hall.

Needle Selection, Handling and Stock Control

Correct selection and disciplined stock control set the floor for breakage rate. A needle must match the machine gauge, length and butt specification exactly, must never be mixed across batches within one cylinder, and must be genuine rather than counterfeit or reground, because selection errors produce failures that no amount of maintenance can prevent.

Matching Gauge, Length and Butt Type

Gauge is the most important parameter, because needle thickness is matched to needle spacing and, through it, to the yarn count the machine can knit. Running a coarse yarn on a fine gauge needle does not simply produce a tight fabric, it forces the hook to draw a loop larger than its design and the needle bends or fractures. The vocabulary and classification of knitting machines exists because these dimensions are not interchangeable between machine types.

Batch Mixing, Counterfeit and Reground Needles

Needles from different batches differ by microns in hook geometry, latch clearance and butt height. Individually those differences sit inside specification, but mixing them in one cylinder produces uneven loop lengths and concentrates load on whichever needles sit slightly proud. Installing one new needle beside a worn one carries the same risk, and regrinding restores the profile without restoring the material underneath. When a section becomes chronic, the answer is a matched set.

What Is the Cause of Continuous Needle Breaking?

Continuous breakage at the same position after a needle has been replaced is almost always caused by something left behind. A fragment of the first broken needle lodged in a trick, a sinker gap or the cam track strikes each subsequent needle at the same point in its stroke, so every replacement fails the same way. In a smaller number of cases the cause is a worn cam or deformed trick that was never corrected.

A needle rarely breaks into two pieces that both fall clear. The hook end usually drops into the fabric or the needle bed, while the butt end can stay wedged in a trick or be thrown into the sinker ring. Restart after a simple swap and that fragment sits in the path of the new needle. Clearing the zone takes longer than replacing the needle, which is exactly why it gets skipped.

  1. Stop the machine and lock it out before reaching into the knitting zone.

  2. Recover every part of the broken needle and clear the fabric from that area.

  3. Sweep the full circumference with a magnet and compressed air, not only the affected feeder.

  4. Inspect each trick in the sector under direct light for embedded fragments.

  5. Check the cam and sinker at that position for fresh impact marks.

  6. Run the machine empty at low speed for several revolutions before reloading yarn.

Breakage that migrates around the cylinder after each repair is the same problem in another form: fragments are being carried by the fabric or the air flow, so the whole zone needs cleaning rather than one position.

the Cause of Continuous Needle Breaking.webp

A Preventive Routine That Holds Breakage Down

Breakage falls and stays low when diagnosis is converted into a fixed inspection cycle and a written record. The routine matters less for its individual tasks than for the fact that it is performed in the same order, at the same interval, by the same person, every week, because consistency is what turns a maintenance programme into a measurable rate.

Interval

Checks that most directly affect needle life

Every shift

Blow down the zone, verify oil level and nozzle alignment, test stop-motion sensors, scan for bent needles

Weekly

Inspect cam screws, sinker clearance and tricks, check belt tension and oil filter, audit tension at each feeder

Monthly

Measure cylinder and dial runout, check gearbox lubrication, verify level at four points, review the log

After a part change

Confirm needle type, gauge and butt, reset timing, return to speed in steps

Daily, Weekly and Monthly Checks

Shift level work keeps the zone clear and the oil film intact, because both degrade continuously and both fail silently. A trick carrying an hour of fly looks identical to a clean one from outside, and a nozzle that has drifted two millimetres still sprays oil, just not where the track needs it. Monthly work targets geometry instead, since runout and concentricity explain breakage that no amount of cleaning will fix.

Tracking Needle Life by Yarn Batch

Two numbers turn breakage into a managed metric: needles consumed per 1,000 running hours, and the hours at which a cylinder set is renewed. Log every failure with four fields, which are machine, feeder position, needle position and yarn lot. If breakage follows the machine, the fix is maintenance. If it follows the feeder, the fix is a component. If it follows the yarn lot, the fix is purchasing, and the log becomes evidence rather than opinion.

FAQ

The three questions below cover the decisions that follow a diagnosis: what a broken needle can damage besides itself, how many spares to hold, and why breakage rates move with the seasons.

Can a single broken needle damage the cylinder?

Usually not, but the exceptions justify an inspection. A clean fracture in the hook or latch generally leaves the trick undamaged. A needle that breaks at the butt, or a fragment caught between needle and cam, can score the trick wall or chip the cam track. Scoring is the worse outcome, because a scored trick holds every later needle slightly off position and the machine then breaks needles there until the cylinder is repaired.

How many spare needles should a mill keep in stock?

A practical baseline is one complete cylinder set per machine plus a float of roughly five percent for single replacements. The number that governs stock is the renewal interval, since a mill renewing sets on a defined running hour basis consumes far fewer needles than one replacing single needles every shift. Hold stock as matched sets by gauge and butt type, because a partial set is what tempts an operator to mix batches.

Does needle breakage increase in dry or humid seasons?

Both extremes raise it. Dry air makes yarn brittle and increases fibre shedding, so more fly reaches the tricks. Humid air raises yarn friction and moisture regain, so the needle works against a heavier, tackier yarn and the hook carries more load. Stabilise the knitting hall rather than chasing the yarn, since steady temperature and humidity remove the swing that otherwise appears in the record as an unexplained seasonal peak.

Home
About Us

WELLKNIT was founded in Taiwan since 1987, and in 1995, we set up the production base in Quanzhou, Fujian, is the first Taiwan-funded weft knitting machine manufacturer to take root in Quanzhou.

Product Category

Contact Us

  CN: No. 189, Lu'an, Jincuo Village, Dongyuan Town, Quanzhou Taiwanese Investment Zone
  CN:0086-595-22632339
     TW:00886-3-3798292
 
market@wellknit.com.tw
    winnie@wellknit.com.tw
Subscribe
Sign up for our newsletter to receive more.
 
Copyright © 2021 Wellknit Textile Technology Co.,ltd. All rights reserved. Sitemap.