Publish Time: 2026-11-02 Origin: Site
Sportswear is the most demanding segment of the knitted fabric market. A leggings program may require four-way stretch, opaque recovery after repeated washing, fast moisture transfer and a surface that prints cleanly. Buyers audit weight, shrinkage and stretch recovery as closely as they audit colour. That changes the purchasing question: not which frame is fastest or cheapest, but which machine can reproduce an approved fabric, batch after batch.
You choose a circular knitting machine for sportswear by working backwards from the fabric specification, not forwards from a catalogue. Fix the knit structure, weight, width, stretch and recovery first, then select the platform, gauge, cylinder diameter, feeder count and elastane system that can hold that specification repeatably. Any frame that meets those limits with stable running efficiency is a candidate, however its brochure ranks on speed.
This guide follows that sequence from the fabric brief to the sample trial behind the quotation.
Sportswear is a family of structures sharing an end use, and each one demands different needle selection, sinker geometry, yarn feeding and take-down. A frame chosen for a lightweight singlet will not produce a good compression tight, even when both fabrics go to the same brand.
Weight in knitting is governed mainly by loop length and yarn count, so one machine at one gauge covers a wide weight range by changing stitch length. That flexibility means "medium weight jersey" gives a supplier nothing to quote against. The brief should fix structure, target GSM, finished width, stretch direction, recovery target and shrinkage allowance.
Single jersey: light, breathable, moderate stretch, for training tees and base layers.
Pique and mesh: textured or open surfaces for ventilation and panels.
Interlock: double knit, smooth on both faces, opaque and stable, for leggings.
Rib: highly elastic, for waistbands, cuffs and fitted panels.
Spacer double knit: two connected layers for padded zones.
Fleece and terry: looped or brushed backs, for warm-up suits.
Each structure implies a needle arrangement. Single-faced fabrics need one cylinder. Interlock, rib and spacer need a cylinder plus a dial. Engineered ventilation or branding needs electronic selection.
Structure | Typical GSM | Platform |
Plain single jersey | 120 to 180 | Single jersey, 3 or 4 track |
Elastane single jersey | 170 to 240 | Single jersey with elastane feeder |
Pique and mesh | 150 to 220 | Multi-track single jersey |
Interlock | 180 to 280 | Double jersey, interlock cams |
Rib | 200 to 320 | Double jersey, rib cams |
Fleece and terry | 240 to 400 | Three-thread fleece platform |
Confirm these bands against a physical sample; stitch length and finishing contraction move the final weight.
Three platform families cover most sportswear: single jersey for light and stretch fabrics, double jersey for structure and compression, and jacquard for pattern and engineered zones. Most mills need a mix rather than one universal frame.
A single jersey machine forms loops on one face only, giving a light fabric with a distinct face and back. A double jersey machine adds a dial, so both needle beds hold loops at the same feeder and produce a thicker, more opaque, more stable fabric.
A single circular knitting machine is the workhorse of athletic basics. Four-track cams allow knit, tuck and miss combinations for pique and mesh without changing the cylinder, and an additional feeder run introduces elastane under controlled draft. Feeder density usually sits at 3 to 4 per inch of diameter, and the upper end pays off only if tension stays stable across the creel.
Where the program needs opacity, compression or shape retention, a double circular knitting machine is the correct starting point. Interlock resists curling and holds width through laundering, which is why it dominates leggings. Rib configurations serve waistbands, and many frames convert between the two by rearranging cams. Double jersey runs slower and costs more, so let the fabric decide.
Electronic selection changes the economics of small orders. A computerized jacquard machine stores patterns in the controller, so a design change is a file change rather than a cam rebuild. The trade-off is complexity: jacquard uses feeders for selection rather than continuous delivery, so output estimated from feeder count will be overstated.
Three-thread fleece for warm-up ranges is a separate platform, not a conversion kit for the jersey line.
Gauge, diameter and feeder count define what a machine can do, and none can be changed cheaply after delivery. Gauge fixes yarn range and surface fineness, diameter fixes finished width, feeder count fixes output.
Gauge is the number of needles per inch of cylinder circumference. It is machined into the cylinder, dial and cam box, so a frame bought at the wrong gauge cannot be rescued by adjusting stitch length.
Higher gauge means finer needles and a shorter pitch, allowing finer yarns and lighter fabric but narrowing tolerance for yarn quality, humidity and tension. The relationship between needle density, yarn count and weight is covered in this guide to circular knitting machine gauge.
Gauge | Yarn range | Typical GSM | Sportswear use |
E18 to E22 | Ne 16 to 24, 200D to 350D | 220 to 320 | Heavy jersey, fleece face |
E24 to E26 | Ne 24 to 32, 120D to 200D | 170 to 240 | Leggings, training tees |
E28 to E32 | Ne 30 to 45, 70D to 120D | 140 to 200 | Fine jersey, compression tops |
E36 to E40 | Ne 50 to 80, 20D to 60D | 90 to 150 | Base layers, micro mesh |
Two costs are easy to miss at the fine end: finer needles break on slubs, and fine gauge is more sensitive to lint and humidity. The highest available gauge is rarely the most profitable choice unless the product requires it.
Apparel concentrates on 30, 32, 34 and 36 inch cylinders; a 30 inch tube flattens to about 47 inches and opens to roughly 2.4 metres before contraction. Work backwards from the finished width the marker requires, add shrinkage from dyeing and stentering, allow for edge loss, then choose the cylinder. A frame one size too small cannot be widened later, and one size too large wastes width on every roll.
Each feeder knits one course per revolution, so courses per minute equals speed multiplied by feeder count. Feeder density matters more than the RPM printed on the specification sheet.
Cylinder | Feeders | RPM | Courses per hour | Output at 180 GSM |
30 inch | 72 | 22 | 95,040 | about 23 kg |
30 inch | 90 | 24 | 129,600 | about 32 kg |
34 inch | 102 | 22 | 134,640 | about 37 kg |
38 inch | 114 | 20 | 136,800 | about 42 kg |
Output assumes 1,500 courses per metre, 2.4 square metres of tube per running metre and 85 percent efficiency. Real figures vary with stitch length, yarn and stoppages, so compare configurations rather than treating the table as a promise.
Plating places elastic yarn behind the face yarn so it stays hidden; laying in introduces it as a separate course for higher stretch at the cost of surface texture. Positive feeding with individual motor drives holds draft constant, which separates a fabric that recovers from one that grows during wear. Ask for the number of elastane positions, the draft range and the maximum elastane percentage at target weight.
Two machines with identical gauge, diameter and feeders can behave very differently across a year of production. The difference is in yarn feeding, take-down and fault detection, because a fabric that passes the first bulk and drifts by the fifth is worthless.
The most common complaint is gradual change: weight drifting within a roll, width varying between rolls, faint bands appearing after dyeing. These are process symptoms, traceable to feeding and tension. Positive feeding holds stitch length constant as bobbin diameter changes, and on elastane small draft variations show up as bands after heat setting.
Tubular take-down flattens fabric into a rope and costs least, but the fold line can leave a crease that shows after dyeing. Open-width slits and spreads in line, improving cutting yield, and for high-elastane sportswear it often decides whether a roll is first or second grade.
Defect | Likely cause | Prevention |
Horizontal barré | Uneven tension or inconsistent draft | Positive feeding, single yarn lot |
Vertical needle lines | Worn needles, damaged sinkers | Needle and sinker inspection |
Spirality and skew | Twist imbalance, take-down tension | Twist-controlled yarn, balanced take-down |
Oil marks | Excess lubrication | Metered oiling, nozzle checks |
Sample long enough to expose drift, and repeat measurements after the real finishing route.
Sportswear is bought against performance claims, so the machine specification should be tied to measurable outcomes. Moisture management, stretch recovery, pilling and dimensional stability carry the most weight in a brand's technical file.
Many purchases fail quietly here, and the gap surfaces only when bulk fabric is rejected at inspection.
AATCC TM195, Liquid Moisture Management Properties of Textile Fabrics, places a synthetic sweat dose on the skin side of a specimen and records wetting time, absorption rate, spreading speed and one-way transport on both faces. A fabric that absorbs quickly but holds liquid on the skin side scores poorly, so structure and finishing matter as much as blend.
Elastic performance is measured as stretch under load and growth after that load is removed. ASTM D2594/D2594M, Standard Test Method for Stretch Properties of Knitted Fabrics Having Low Power, is the reference for comfort stretch apparel, and the growth value predicts whether a tight bags at the knee. Because growth depends on loop geometry and elastane draft, the machine can influence it directly.
Pilling matters for brushed and fleece structures, and abrasion resistance predicts wear life in high-friction zones such as inner thighs. Measure dimensional stability after the real dyeing and heat-setting route, not on greige.
Convert quoted capacity into cost per kilogram before comparing offers, because a cheaper frame at lower efficiency often costs more per kilo than a faster one.
Courses per hour equal revolutions per minute multiplied by feeder count and by sixty. Dividing by courses per metre gives fabric length, and multiplying by weight per running metre gives kilograms.
For a 30 inch frame with 90 feeders at 24 RPM, 1,500 courses per metre and 2.4 square metres of tube per running metre:
Courses per hour: 24 x 90 x 60 = 129,600
Fabric length: 129,600 / 1,500 = 86 metres
Weight per metre at 180 GSM: 2.4 x 0.18 = 0.43 kg
Gross output: 86 x 0.43 = 37 kg per hour, about 32 kg net at 85 percent efficiency
Five costs dominate the result and only one appears in a quotation: yarn waste, changeover time, energy, needle and sinker consumption, and maintenance. A frame ten percent cheaper that needs twice the needle changes loses that advantage within a year.
A written specification turns a conversation into a comparison, and it fixes acceptance criteria before the deposit is paid.
Fabric sample or photograph, with the structure named
Fibre composition and yarn count for every yarn
Target greige and finished weight in GSM
Finished width, and whether the roll is tubular or open width
Stretch direction, percentage and recovery target
Elastane type, percentage and feed method
Dyeing and finishing route, including heat-setting conditions
Gauge, diameter and feeder count if already fixed by the marker
A supplier who replies with a model number without questioning the brief will rarely support the project well.
It depends on product mix rather than volume. A line making only lightweight jersey can start with one frame and add capacity as orders grow. A line serving both light tops and compression bottoms needs one frame of each type, because neither structure runs economically on the other platform.
Yes, when both are double-knit and the gauge, diameter and elastane system suit the heavier fabric. The limit is the gauge band rather than the platform: a frame set for fine interlock struggles with heavy compression structures.
Often yes. Swimwear needs finer gauge, higher elastane content and tighter dimensional control; underwear needs softer hand. A frame at the fine end of the range, with enough elastane positions, generally crosses over.
How to Choose a Flat Knitting Machine for Sweater Production
How to Choose a Circular Knitting Machine for Sportswear Fabrics
Terry vs. Fleece Circular Knitting Machines: Key Differences
Rib Knitting Machine vs. Interlock Knitting Machine: Which Should You Choose?
How to Choose Circular Knitting Machine Gauge for Your Fabric
WELLKNIT was founded in Taiwan since 1987, and in 1995, we set up the production base in Quanzhou, Fujian, is the first Taiwan-funded weft knitting machine manufacturer to take root in Quanzhou.