English
繁體中文
العربية
Français
Pусский
Español
Português
Tiếng Việt
ไทย
Türk dili
Bahasa indonesia

You Are Here: Home » Blog » Guide » How to Choose a Flat Knitting Machine for Sweater Production

How to Choose a Flat Knitting Machine for Sweater Production

Publish Time: 2026-11-12     Origin: Site

Most sweater programmes fail before the first panel leaves the machine. A sweater flat knitting machine bought on the wrong gauge, bed width or number of systems is expensive to correct, and the catalogue spans beds from 52 to 100 inches, gauges from 3GG to 18GG and one to three knitting systems, at prices from about 5,000 to above 80,000 USD.

Choose the machine by working backwards from the garment. Gauge follows yarn count and target fabric weight, bed width follows the widest panel, system count follows monthly volume, and architecture follows how you will assemble the sweater. Only then does price become a fair comparison, because a cheap machine that cannot knit your widest panel is not cheap.

The sequence below follows that order, from product profile to acceptance test.

Start With the Sweater, Not the Machine

Start with the product range: silhouettes, target fabric weight in grams per square metre, stitch structures, colours per row, widest panel and annual volume per style. Each maps to one machine parameter, and that mapping, not the catalogue, sets the specification.

Most mistakes come from choosing the machine first and fitting the product to it. A 12GG machine bought for chunky cables will not pass the yarn through its latches, and a 52 inch bed cannot knit a 140 cm coat panel. Both were specified against the wrong input.

The right input is the approved technical pack of a garment already knitted somewhere, in-house or by a subcontractor. Where none exists, knit three: the heaviest, the finest and the widest style. Those define an envelope that every machine you shortlist must cover.

Build a Product and Volume Profile

Write the profile before approaching suppliers, or they will shape the conversation around their stock. It needs silhouette families and size range, fabric weight per family rather than an average, the structures actually sold, colours per row, trim programme, annual volume and style changes per month.

Translate a Tech Pack Into Machine Requirements

Once the profile exists, the translation is mechanical.

Garment attribute

Machine parameter it sets

Target fabric weight

Gauge band, which fixes the usable yarn count

Widest panel, measured flat

Bed width, a limit no setting can exceed

Stitch structures

Cam functions: knit, tuck, miss, transfer, racking travel

Colours per row

Yarn carriers, plus intarsia carriers if needed

Annual volume and style changes

Number of systems, and number of machines

Assembly route

Architecture, from blank knitting to knit to shape

Match Gauge to Yarn Count and Fabric Weight

Gauge is the number of needles per English inch, and it fixes both the finest yarn the machine can run and the weight of the fabric. Choose the gauge band from the target fabric weight, then confirm the yarn count inside that band, because the two are one decision.

Coarse gauges leave room for thick yarn and give visible stitch definition; fine gauges form smaller loops for smooth, light fabric. Mismatch is costly both ways: thick yarn on a fine machine breaks and damages needles, while fine yarn on a coarse machine gives loose loops and panels that grow after washing.

Gauge

Yarn count, fabric weight and typical product

3GG to 5GG

Pitch 8.47 to 5.08 mm. Resultant Nm 3 to 9, fabric 420 to 850 g/m2, garment 400 to 850 g. Chunky cables and fisherman rib

7GG to 9GG

Pitch 3.63 to 2.8 mm. Resultant Nm 10 to 17, fabric 320 to 450 g/m2, garment 280 to 450 g. Crewnecks and polo knits

10GG to 12GG

Pitch 2.54 to 2.12 mm. Resultant Nm 16 to 30, fabric 180 to 350 g/m2. The workhorse range

14GG to 16GG

Pitch 1.81 to 1.41 mm. Resultant Nm 26 to 40, fabric 150 to 220 g/m2. Fine merino and lightweight layers

18GG

Pitch around 1.27 mm. Resultant Nm 40 and finer, under 160 g/m2. Ultra fine luxury knits

Gauge and Yarn Count Must Be Decided Together

The orientation rule is that resultant metric count at the feeder falls between 1.5 and 2.5 times the gauge number, so 7GG runs Nm 10 to 17 and 12GG runs Nm 18 to 30. Two identical ends halve the resultant count. Because gauge has been measured on both a 1 inch and a 1.5 inch scale, convert quoted figures to needles per inch and confirm on a knitted sample.

When a Multi-Gauge Machine Makes Sense

Interchangeable needle sections let one bed run 3GG, 5GG and 7GG, or 8GG to 12GG, covering two seasons with one purchase. Each changeover costs production time and fresh tension settings, doubles the needle inventory and demands operators competent on every configuration. Below a few thousand pieces per gauge per year, a second machine is the better buy.

Choose the Right Machine Architecture

The workhorse is a computerized V-bed flat machine with two needle beds facing each other. Only a double bed can knit true rib, transfer stitches between beds and shape a panel by widening and narrowing, which is why single bed machines cannot knit rib and circular machines cannot shape a panel at all.

The V-bed arrangement lets the beds hold loops alternately so stitches can be moved, held and returned, which is what makes rib, cables and armhole narrowing possible without cutting.

Computerized Versus Mechanical Flat Bed

Mechanical machines select needles with cards or chains. They survive for extreme coarse gauge and craft effects, but pattern changes need physical setup, tension varies between operators and shaping is largely manual. Where a stitch must be reproduced across repeat orders, the computerized pattern file becomes the specification.

Single Bed, Double Bed V-Bed, and Whole Garment

Three routes sit on the same machine family, and the choice is commercial as much as technical.

Architecture

Output and trade-offs

V-bed, blank knitting

Fabric cut to shape and sewn. Fast per panel, but wastes yarn and relies on overlock seams

V-bed, fully fashioned

Panels knitted to shape and linked. Near zero cutting waste and stronger seams

Whole garment

Knitted in one piece, no linking. Above 80,000 USD, slower, and demands strong programming

Fully fashioned knitting is where most programmes land, and the knit to shape logic explains why flat beds dominate heavier knitwear. A circular machine knits a tube instead, so a sweater made on one must be cut, which curls the edges, wastes yarn and puts a seam where a selvedge belongs.

Size the Needle Bed Width Correctly

Set bed width from the widest panel plus a margin, and treat it as a hard limit. A wider panel cannot be knitted at any setting, and splitting it adds a visible seam plus a linking operation that costs money on every piece.

Measure the widest panel flat after relaxation and add 5 to 10 cm for selvedge, take-down grip and the outer needles you cannot rely on. Check the trim programme too, since a flat knitted collar can be wider than expected. Bodies usually fall between 50 and 65 cm, so a 52 inch bed covers most of a knitwear range.

Bed width

What it realistically covers

52 inch (132 cm)

Most body panels, sleeves, collars and trims. The common volume size

60 inch (152 cm)

Longer bodies, oversized drop shoulders, wide sleeves

66 to 72 inch (168 to 183 cm)

Longline bodies, coat panels, knit dresses, plus size grading

80 inch (203 cm)

Very long dresses and coats, wide blanket style panels

100 inch (254 cm)

Blankets only, rarely garment panels, and the width costs floor space

A wider bed adds frame mass, price and footprint, and the carriage travels further for every course, which lowers output on narrow panels.

Decide How Many Knitting Systems You Need

Each system is one set of cams and feeders completing one course per carriage pass. Three systems approach three passes in one, but the real gain is 2 to 2.5 times a single system once shaping and stops are counted, so buy systems for the volume you can keep loaded.

System count

Real output and best use

Single system

Baseline. Sampling, complex intarsia, coarse gauge where yarn limits speed

Two system

About 1.8 to 2 times baseline. Mid volume, moderate patterning

Three system

About 2.2 to 2.5 times baseline on plain and rib. Bulk programmes

Four system and above

More courses per pass, heavier maintenance, fewer qualified technicians

Turn Rated Speed Into Real Output

Brochure speeds of 1.2 to 1.6 m/s mean little alone, because a machine spends much of its life reversing, transferring, changing yarn and stopped for faults. An estimate built from five steps is more honest:

  1. Take the stroke length, panel width plus carriage overrun

  2. Divide by sustained speed and add 0.3 seconds per end for reversal

  3. Divide courses by the number of systems to get the passes

  4. Multiply passes by time per pass for pure knitting time

  5. Apply an efficiency factor of 0.55 to 0.7 for transfers and stops

A 12GG plain body of 300 courses on a one metre stroke gives about 200 seconds of pure knitting on three systems, or 8 to 12 minutes of real time. A five piece sweater occupies 45 to 60 minutes, so 20 hours yields 20 to 25 garments, while a 3GG cable takes three to four times longer.

Check the Structural Features That Decide Uptime

Four mechanisms decide whether a machine earns its keep: needle selection, transfer and racking, take-down and sinker control, and yarn carriers. Weakness in any one shows up as a structure you cannot knit, not merely a speed you cannot reach.

Mechanism

What it decides and how to verify

Needle selection

Colours per row and jacquard resolution. Ask for a fine motif sample

Transfer and racking

Rib, cables, links and the narrowed armhole edge. Inspect a shaped panel

Take-down and sinkers

Panel stability and openwork. Measure a full width panel after relaxation

Yarn carriers

Colour blocks and plating. Count carriers and confirm intarsia carriers are included

Stop motions

Yarn break, needle break and racking fault must stop the machine, not knit on

Transfer, Racking and Take-Down

Transfer is mechanical rather than a setting: the cams must move stitches from either bed while another system keeps knitting. Racking travel, usually 2 inches each way, decides which cables are possible. Take-down, controlled in 24 or more levels, holds tension through shaping and determines whether a panel measures correctly after washing. Intarsia also needs dedicated carriers, or colour blocks become jacquard with floats that snag.

Evaluate the Control System and Design Software

The control system decides daily productivity, because a machine can only produce patterns your team can programme. Confirm the software is learnable in weeks, that files exchange with customers and your existing library, and that faults are logged for remote diagnosis.

A sweater flat knitting machine with a large pattern library, USB and network transfer, and parameters displayed in your operators' language is productive from month one; one that needs a single specialist to convert every design idles when that person is away. Test four things: time an import of your own design file, ask how alarms are logged, ask whether a controller board is stocked regionally, and confirm training runs on your patterns.

Calculate Total Cost of Ownership, Not Purchase Price

Purchase price is the smallest part of the decision. Landed cost, installation, programming time, needles, energy and downtime over five years outweigh the gap between a cheap and a well specified machine, and utilisation decides payback more than any specification.

Indicative prices run from 5,000 to 15,000 USD for an entry level 52 inch two system machine, 20,000 to 60,000 USD for multi system with full jacquard, and above 80,000 USD for whole garment. Compare cost per piece at your own volume instead.

Cost element

Basis and typical value

Depreciation

30,000 USD over five years at 12,000 pieces a year, about 0.50 USD per piece

Direct labour

One operator to four machines, about 0.23 USD per piece

Energy

3.5 kW average draw over 20 hours a day, about 0.16 USD per piece

Needles and consumables

Annual replacement budget, about 0.10 USD per piece

Maintenance

Scheduled service and parts, about 0.13 USD per piece

Total conversion

About 1.10 USD per piece, excluding yarn and finishing

If in-house knitting saves two dollars a piece against outsourced conversion, a 30,000 USD machine making 12,000 pieces a year pays back in about 15 months. Below 40 percent utilisation it never does, which is why volume must be settled before the model.

A 52 inch machine needs about 2.85 by 0.95 m of floor, an 80 inch about 4.0 by 1.0 m, and a 100 inch about 4.7 by 1.05 m at close to 1.7 tonnes, with pallet truck access and clearance behind the bed. Smaller machines run on single phase 220V and larger ones need three phase with stable voltage. Needles are consumable, so keep an annual allowance and working stock at the machine.

Vet the Supplier Before You Sign

A machine is only as good as the support behind it. Trial knit with your own yarn on a representative pattern, fix the acceptance test in writing before the deposit, and confirm that needles, cams and control boards are stocked regionally.

Trial Knit on Your Own Yarn

Send your own yarn in your own counts and ask for the three styles that define your envelope. The same Nm 2/28 wool that runs cleanly on one bed may break repeatedly on another because of feeder geometry, so the trial must produce panels you can measure, wash and inspect.

Acceptance Test, Documentation and Service Response

Write these into the contract and hold a balance against them:

  1. Witnessed knitting of three representative styles at the ordered gauge and width

  2. Measured output over an eight hour run, with efficiency stated

  3. Dimensional check after relaxation and one wash

  4. Function test of every stop motion

  5. Spare parts list with prices and delivery times

  6. Drawings and a parts manual in your language

  7. Operator and programmer training on your patterns

  8. Warranty stated separately for bed, carriage and controller

FAQ

Three questions surface once the specification is settled: how many machines the order book needs, whether a used machine is a sensible entry, and what to stock from the first week.

How many machines will a monthly output target require?

Divide the monthly target by working days, then by realistic daily output for your heaviest style, and add 15 to 20 percent headroom for sampling and changeovers. A target of 8,000 pieces over 22 working days needs about 364 a day, which at 20 to 25 pieces per machine implies 15 to 18 machines. Plan on peak season, because a fleet sized to the annual average will be short when it matters.

Is a used sweater flat knitting machine a realistic entry point?

Yes, with conditions. Well maintained used machines knit the same panel as new ones at a fraction of the price, but the risks are hidden: beds worn enough to lose gauge across the width, carriage guides with play, unsupported controllers and needle types out of production. Inspect with a technician, knit a full width panel and measure five points across it, and price a re-needle before agreeing. Used equipment suits sampling rooms and coarse gauge basics, not fine gauge work that must hold tolerance.

Which spare parts should be stocked from day one?

Hold needles at 2 to 3 percent of the bed needle count, roughly 15 to 20 on a 52 inch 12GG bed of about 620, plus sinkers, one spare cam segment per system, feeder belts, a take-down roller covering, fuses and the sensors most likely to fail. Order them with the machine, because freight on a small parts order often exceeds the parts and a missing needle type can idle a line for a week.

RELATED ARTICLES

About Us

WELLKNIT was founded in Taiwan since 1987, and in 1995, we set up the production base in Quanzhou, Fujian, is the first Taiwan-funded weft knitting machine manufacturer to take root in Quanzhou.

Contact Us

  CN: No. 189, Lu'an, Jincuo Village, Dongyuan Town, Quanzhou Taiwanese Investment Zone
  CN:0086-595-22632339
     TW:00886-3-3798292
 
market@wellknit.com.tw
    winnie@wellknit.com.tw
Subscribe
Sign up for our newsletter to receive more.
 
Copyright © 2021 Wellknit Textile Technology Co.,ltd. All rights reserved. Sitemap.